Looking for:
2009 toyota corolla manual |
2009 toyota corolla manual.2009 Toyota Corolla Owner’s Manual
Route the ignition switch connectors on the main harness under the steering column. Secure the main harness along it's routing with the cable ties provided.
Be sure that the harness is clear of all sharp, hot, moving objects. Route pin switch wire through the bulkhead grommet nipple from "inside" of the vehicle. Apply a good sealant to seal grommet against water entry. Install the "black" flat washer on the pin switch and guide through the opening on upper radiator support. Hood Switch Location 3. Install "star washer" nut on pin switch wire and connect pin switch wire to pin switch as shown.
Thread "starwasher" nut on pin switch and tighten. Plug the 5 pin end of the harness into the matting connector on the main control module. Route the harness towards the shock sensor, where it will not interfere with any sharp or moving objects. Secure the harness along the routing path using the cable ties provided.
When installing female T - Tap connectors, be sure the wire is located inside the wire channel of the female T - Tap connector before closing connector over the wire with pliers Figure D. Refer to page 10 for additional details. Refer to page 11 for additional details. The recommended sensitivity setting for the shock sensor is setting 2!
Shock Sensor Disconnect the Ignition Switch Connector A1 and plug in the security main harness into the ignition switch connectors. Plug one end of the extension wire into the DARK GREEN WIRE on the alarm harness, route the extension wire through the bulkhead grommet on the driver's side of the vehicle, and plug the other end of the extension onto the hood pin switch. Pin 6 Black Headlights 6.
Attach the extension wire to the alarm BLUE wire and route to the glove box, passenger side area. Refer to page 13 for additional details.
Refer to page 14 for additional details. Pin 6 Violet Headlights 6. Test BOTH remote transmitters, one at a time. Press and release the "LOCK" button. If the LED light on the transmitters fails to glow, you need to check the transmitter battery. Sit in the driver's seat, insert the ignition key and turn to the ON position.
Press the valet control switch and verify that the LED light responds. Press the "LOCK" button, the parking lights will flash once, all doors will lock, headlights come on for 20 seconds. Press the "UNLOCK" button, the parking lights will flash twice, driver's door only will unlock, headlights come on for 20 seconds.
Put all vehicle windows down and close hood and all doors. Press and release the "LOCK" transmitter button. All doors should lock, parking lights flash once, horn chirps once, headlights come on for 20 seconds and the LED should flash slowly. Note: If the parking lights flash three times and the horn chirps three times, check for an open hood or door.
Press the "UNLOCK" button, the horn chirps 2 times, parking lights flash 2 times, headlights come on for 20 seconds, driver's door only unlocks. Press and hold the "RED" button to test the "Panic" function. The alarm should blow the horn in short, continuous blast, parking lights should be flashing. Press the "LOCK" button to arm the system.
With the open palm lightly slap the "A" pillar by the driver's windshield. You should hear short chirps from the vehicle horn. Allow a few seconds for the shock to settle, then conduct the same check at various points around the vehicle. Sensitivity can be adjusted at the shock sensor for best response. Slap the vehicle at the "A" pillar with slightly more force.
The vehicle should go into full alarm. Rearm the vehicle and conduct the same check at various points around the vehicle. Page 15 of 17 Rear Cover F. Set in the driver's seat with all the doors closed. Insert the ignition key and turn to the start position. The starter should not crank the engine. Turn to the start position. The starter should crank the engine. Exit vehicle. Use the key to unlock and open the driver's door. The alarm will sound. Enter the vehicle, insert the ignition key and turn to the on position.
Press the valet control switch once, the alarm should deactivate and the vehicle should now start. Press the "LOCK" button, the system should arm and lock all doors. Rearm the security system by pressing the "LOCK" button. Open any door or hatch. The system should simultaneously sound the horn and flash the parking lights.
The system should sound 4 chirps of the horn, the parking lights should flash 4 times, indicating vehicle intrusion. The LED should indicate the point of intrusion after disarming the system. Observe the LED for 1, 2, or 3 flashes. Compare your observations to the following. If the smart key system or the wireless remote control function does not operate, or the detection area becomes smaller, the battery may be depleted.
Page 51 Opening, closing and locking the doors and trunk Even if the electronic key is not inside the vehicle, it may be possible to start the engine if the electronic key is near the window. The doors may unlock if a large amount of water splashes on the door handle, such as in the rain or in a car wash.
Page 52 Opening, closing and locking the doors and trunk When an alarm sounds: Take appropriate measures according to the following table. Alarm Situation Correction procedure Tried to lock the doors Retrieve the elec- using the entry function tronic key from the while the electronic key is vehicle and lock the still inside the vehicle Page 54 Opening, closing and locking the doors and trunk Certification for the smart key system For vehicles sold in the U.
Operation is subject to the following two conditions: 1 this device may not cause harmful interfer- ence, and 2 this device must accept any interference received, including interference that may cause undesired operation. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves. Page Wireless Remote Control Opening, closing and locking the doors and trunk Wireless remote control if equipped The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle.
Page 57 Opening, closing and locking the doors and trunk Door lock buzzer If a door is not fully closed, a buzzer sounds continuously for 10 seconds if an attempt to lock the door is made.
Fully close the door to stop the buzzer, and lock the vehicle once more. Page 58 Opening, closing and locking the doors and trunk Security feature If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.
Page 59 Opening, closing and locking the doors and trunk Customization that can be configured at Toyota dealer Settings e. Page Doors Opening, closing and locking the doors and trunk Doors The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch.
Page 61 Opening, closing and locking the doors and trunk Inside lock button Locks the door Unlocks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position.
Rear door child-protector lock The door cannot be opened from inside the vehicle when the locks are set. Page 62 Opening, closing and locking the doors and trunk Automatic door locking and unlocking systems vehicles with power door lock system The following functions can be set or cancelled: Function Operation Shift position linked Shifting the shift lever out of P locks all door locking function doors.
Page 63 Page 64 Vehicles without smart key system The key is in the engine switch and either of the front door is open. Customization that can be configured at Toyota dealer Settings e. Opening, closing and locking the doors and trunk Trunk The trunk can be opened using the entry function, wireless remote control, key or trunk opener.
Page 66 Opening, closing and locking the doors and trunk Trunk opener cancelling system To protect luggage stored in the trunk against theft, do the following procedure. Turn the master key vehicles without smart key system or mechanical key vehicles with smart key system counterclock- wise to lock the trunk opener fea- ture. Page 67 This not only keeps personal belongings from being thrown out, but also pre- vents exhaust gases from entering the vehicle.
When children are in the vehicle Never leave children unattended in the vehicle as they may lock them- selves in the vehicle or trunk, which could cause the child to overheat or suffocate, resulting in death or serious injury. Adjustable components seats, mirrors, steering wheel Front seats Power seat driver's side only Seat position switch Seatback angle switch Seat cushion front angle switch Vertical height adjustment switch Lumbar support switch I n f o r ma t i o n P r o v i d e d b y Page 69 Page 70 Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt.
If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of Page Rear Seats Adjustable components seats, mirrors, steering wheel Rear seats Before folding down the rear seat Stow the rear outside seat belt buckles and move the rear center seat belt buckle as shown.
Folding down rear seatbacks Pull the seatback lever in the trunk for the seatback you wish to fold down. Page 72 Failure to do so may result in death or serious injury. Make sure the seatback is securely locked by pressing forward and rear- ward on the top of the seatback.
Page Head Restraints Adjustable components seats, mirrors, steering wheel Head restraints Front seats Vertical adjustment Push and hold the lock release button when lowering the head restraint.
Removal Pull the head restraint up while pressing the lock release but- ton. Rear seats Adjusting the height of the head restraints Make sure that the head restraints are adjusted so that the center of the head Page 74 Use the head restraints designed for each respective seat. Adjust the head restraints to the correct position at all times.
After adjusting the head restraints, push down on them and make sure they are locked in position. Page Seat Belts Adjustable components seats, mirrors, steering wheel Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle.
Correct use of the seat belts l Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the Page 76 Adjustable components seats, mirrors, steering wheel Adjusting the height of the belt front seats Down Move the height adjuster up and down as needed.
Seat belt comfort guide outside rear seats If the shoulder belt sits close to a person's neck, use the seat belt comfort guide. Page 77 Adjustable components seats, mirrors, steering wheel Buckle, position and release the STEP seat belt.
Seat belt pretensioners front seats The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal collision.
Page 78 Adjustable components seats, mirrors, steering wheel Emergency locking retractor ELR The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully. Page 79 Toyota dealer free of charge. Rear outside seat belt Use the seat belt after passing it through the guide if the seat belt comes free from the guide.
Page 80 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children.
Page 81 Ensure that the belt and tab are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. Replace the seat assembly, including the belts, if your vehicle has been involved in a serious accident, even if there is no obvious damage.
Page 82 Adjustable components seats, mirrors, steering wheel CAUTION Using a seat belt extender Do not wear the seat belt extender if you can fasten the seat belt without the extender. Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or injury in the event of a collision.
Page Steering Wheel Adjustable components seats, mirrors, steering wheel Steering wheel The steering wheel can be adjusted to a comfortable position. STEP Hold steering wheel and press the lever down. STEP Adjust to the ideal position by moving the steering wheel hori- zontally and vertically. Adjustable components seats, mirrors, steering wheel Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions.
Manual anti-glare inside rear view mirror Normal position Anti-glare position Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced. Page 85 Adjustable components seats, mirrors, steering wheel To prevent sensor error To ensure that the sensors operate prop- erly, do not touch or cover them. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.
Page Outside Rear View Mirrors Adjustable components seats, mirrors, steering wheel Outside rear view mirrors Mirror angle can be adjusted using the switch. Select a mirror to adjust. Page 87 When the mirrors are fogged up vehicles with outside rear view mirror defoggers Turn on the mirror defoggers to defog the mirrors. Page 88 Opening and closing the windows Power windows if equipped The power windows can be opened and closed using the following switches.
Lock switch Press the switch down to lock the passenger window switches. Page 89 Operating the power windows after turning the engine OFF Vehicles with smart key system The power windows can be operated for approximately 45 seconds after the Opening and closing the windows Moon roof if equipped Use the overhead switches to open, close, and tilt the moon roof up and down.
Push the switch again to fully open. Page 91 Operating the moon roof after turning the engine OFF Vehicles with smart key system The moon roof can be operated for approximately 45 seconds after the Page 92 Failing to do so may cause death or serious injury.
Do not allow any passengers to put their hands or heads outside the vehi- cle while it is moving. Do not sit on top of the moon roof.
Page Refueling Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. Vehicles without smart key system Turn the engine switch OFF and ensure that all the doors and windows are closed. Page 94 Closing the fuel tank cap When replacing the fuel tank cap, turn it until a clicking sound is heard. After releasing your hand, the cap will turn slightly to the opposite direction.
Page 95 This may cause static electricity to build up, resulting in a possible ignition hazard. When replacing the fuel cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury. Page 96 Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle's painted surface.
Page Theft Deterrent System Theft deterrent system Engine immobilizer system The vehicle's keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle's on-board computer.
Never leave the keys inside the vehicle when you leave the vehicle. Page 98 Theft deterrent system Certifications for the engine immobilizer system for vehicles sold in U. Theft deterrent system Theft prevention labels for U.
These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law. Page Safety Information Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back in the seat. Page Doing so could cause the driver to lose control of the vehicle.
Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
Page Srs Airbags Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. Front airbags Driver airbag and front passenger airbag Can help protect the head and chest of the driver and front pas Safety information The main SRS airbag system components are shown above.
The SRS airbag system is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sensor and an airbag sensor. In certain types of severe frontal or side impacts, the SRS airbag sys- tem triggers the airbag inflators. Safety information Side airbags and curtain shield airbags if equipped The SRS side airbags and curtain shield airbags are designed to inflate when the passenger compartment is subjected to a severe impact from the side.
Depending on the conditions and type of accident, there are times when the curtain shield airbags may deploy inflate in a front impact. Safety information Types of collisions that may not deploy the SRS side airbags and cur- tain shield airbags if equipped The SRS side airbags and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a col- lision to the side of the vehicle body other than the passenger compartment.
Safety information When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. Do not disconnect the battery cables before contacting your Toyota dealer.
Any of the SRS airbags have been inflated. Failure to do so may cause death or serious injury. The driver and all passengers in the vehicle must wear their seat belts properly. The SRS airbags are supplemental devices to be used with the seat belts.
The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag. Page An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained.
The rear seats are the safest for infants and children. Do not drive the vehicle while the driver or passenger has items resting on their knees. Safety information CAUTION SRS airbag precautions Vehicles with side airbags and curtain shield airbags: Do not attach anything to areas such as the door, windshield glass, side door glass, front and rear pillars, roof side rail or assist grip. Curtain shield airbags: Do not hang coat hangers or other hard objects on the coat hooks.
Page Vehicles without side airbags and curtain shield airbags: If the areas where the SRS airbags are stored, such as the steering wheel pad are damaged or cracked, have them replaced by your Toyota dealer. Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer.
Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for the front passenger. Safety information : Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable.
Page Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately. Child restraint systems installed on the rear seat should not contact the front seatbacks. Page Child Restraint Systems The laws of all 50 states of U. Safety information Types of child restraints Child restraint systems are classified into the following 3 types according to the age and size of the child.
Page In an accident, the child can be crushed against the windshield, or between you and the vehicle's interior. Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat.
According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the rear-facing child restraint system is installed on the front passenger seat. Page Installing Child Restraints Safety information Installing child restraints Follow the child restraint system manufacturer's instructions.
Firmly secure child restraints to the rear seats using a seat belt or a child restraint lower anchorage. Attach the top strap when installing a child restraint. Run the seat belt through the STEP child seat and insert the plate into the buckle.
Safety information While pushing the child seat STEP down into the rear seat, allow the shoulder belt to retract until the child seat is securely in place. After shoulder belt retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended. Safety information While pushing the child seat into STEP the rear seat, allow the shoulder belt to retract until the child seat is securely in place. Safety information Removing a child restraint installed with a seat belt Push the release button and fully retract the seat belt.
Installation with child restraint lower anchorages Rear right seat only: Slide the STEP rear center seat belt to the side to prevent it from getting pinched in the lower anchorage.
STEP Latch the hooks of the lower straps onto the anchors. If the child restraint has a top strap, the top strap should be latched onto the anchors. Safety information Child restraint systems with a top strap STEP Secure the child restraint using a seat belt lower anchor, and do the following.
Outside Remove the head restraint. Center Lock the head restraint in place at the lowest position. Open the anchor bracket cover, STEP latch the hook onto the anchor This vehicle is designed to confirm to the SAE J Safety information CAUTION When installing a child restraint system When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder.
The belt should be kept away from the child's neck, but not so that it could fall off the child's shoulder. Page Driving Procedures Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. STEP Set the parking brake. Page Breaking in your new Toyota To extend the life of the vehicle, the following precautions are recommended Driving procedures Operating your vehicle in a foreign country Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel.
Page Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immedi- ately. Do not under any circumstances shift the shift lever to P vehicles with an automatic transmission or R while the vehicle is moving. Driving procedures CAUTION When driving on slippery road surfaces Sudden braking, acceleration and steering may cause tire slippage and reduce your ability to control the vehicle, resulting in an accident.
Sudden changes in engine speed, such as engine braking caused by up- shifting or down-shifting, may cause the vehicle to skid, resulting in an accident. Page The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard.
Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.
After shifting, do not release the clutch abruptly. Doing so may damage the clutch, tran- saxle and gears. Do not rest your foot on the clutch pedal while driving. Doing so may cause clutch trouble. Page If you hear a squealing or scraping noise brake pad wear limit indica- tors Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage can result if the pads are not replaced when needed.
Starting the engine STEP Have the vehicle inspected by your Toyota dealer immediately. Do not depress the accelerator pedal while starting the engine under any circumstances.
Doing so may cause an accident resulting in death or serious injury. Driving procedures Engine ignition switch vehicles without smart key system Starting the engine Automatic transmission STEP Check that the parking brake is set.
To free it, turn the key while turn- ing the steering wheel slightly in either direction. If the engine does not start The engine immobilizer system may not have been deactivated. When starting the engine 2. Page Automatic Transmission Driving procedures Automatic transmission if equipped Select a shift position appropriate for the driving conditions.
Driving procedures Changing shift ranges in S mode multi-mode type Shift the shift lever to the S position and operate the shift lever.
Upshifting Downshifting The initial shift range in S mode is automatically set to 4 or 5. Shift ranges and their functions Shift range Function Page S multi-mode type This may indicate a malfunction in the automatic transmission system.
In this situation, the vehicle will operate as if the shift lever is in D. Page Manual Transmission Driving procedures Manual transmission if equipped Shifting the shift lever Fully depress the clutch pedal before operating shift lever, and then release the clutch pedal slowly.
Maximum allowable speeds Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary. Page Turn Signal Lever Driving procedures Turn signal lever Left turn Right turn Move and hold the lever partway to signal a lane change. The left hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change. Page Parking Brake Driving procedures Parking brake Sets the parking brake Fully set the parking brake U.
Canada while depressing the brake pedal. Releases the parking brake Slightly raise the lever and lower it completely while press- ing the button.
Page Instrument Cluster Pressing and holding the button will reset the trip meter when the trip meter is being displayed. To adjust the brightness of the instrument panel light, turn the button. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Instrument cluster Odometer and trip meter display Odometer: Displays the total distance the vehicle has been driven.
Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently. Page Indicators And Warning Lights Instrument cluster Optitron type meters Non-Optitron type meters I n f o r ma t i o n P r o v i d e d b y Page Have the vehicle inspected by your Toyota dealer immediately if this occurs.
Page Multi-Information Display Instrument cluster Multi-information display The multi-information display presents the driver with a variety of driving-related data, including the clock and the outside tempera- ture. Instrument cluster l Outside temperature Displays the outside air temperature. Instrument cluster l Average vehicle speed Displays the average vehicle speed since the engine was started or since the function was reset.
The function can be reset by pressing the display but- ton for longer than one second when the average vehicle speed is displayed. Instrument cluster When disconnecting and reconnecting battery terminals The following information data will be reset. Clock Average fuel consumption Driving range Average vehicle speed Elapsed time NOTICE The multi-information display at low temperatures Allow the interior of the vehicle to warm up before using the liquid crystal information display.
Operating the lights and wipers Headlight switch side marker, parking, tail, license plate and instrument U. The headlights and all lights listed above turn on. Operating the lights and wipers Daytime running light system To make your vehicle more visible to other drivers, the headlights turn on automatically whenever the engine is started and the parking brake is released. The brightness of headlights will automatically change depending on the darkness of the surroundings.
Page Fog Light Switch Operating the lights and wipers Fog light switch if equipped The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam. Page Windshield Wipers And Washer Operating the lights and wipers Windshield wipers and washer Wiper can be operated manually. Intermittent windshield wiper interval mode if equipped Wiper intervals can be adjusted for intermittent operation.
Page Using Other Driving Systems Using other driving systems Cruise control if equipped Use cruise control to maintain a set speed without using the acceler- ator. Press the button once more to deactivate the cruise control. Using other driving systems Canceling and resuming regular acceleration Cancel Pull the lever towards you to cancel cruise control. The speed setting is also can- celed when the brakes are applied or the clutch pedal manual transmission depressed.
Resume To resume cruise control and return to the set speed, push the lever up. Page If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system.
Contact your Toyota dealer and have your Toyota inspected. Page Driving Assist Systems Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle.
ABS Anti-lock Brake System Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.
You may need to turn the system off to enable you to rock the vehicle in order to free it. EPS operation sound When the steering wheel operates, a motor sound whirring sound may be heard. Contact your Toyota dealer for further information when replacing tires or wheels.
Handling of tires and suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction. Page Driving Information Driving information Cargo and luggage Take notice of the following information about storage precau- tions, cargo capacity and load. Be sure all items are secured in place. Placing the weight as far for- ward as possible helps maintain vehicle balance.
Driving information 6 If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Keep cargo and luggage low, as close to the floor as possible. Never allow anyone to ride in the enlarged trunk. It is not designed for passengers. Page Vehicle Load Limits Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity.
Total load capacity: lb. Seating capacity: 5 occupants Front 2, Rear 3 Seating capacity means the maximum number of occupants whose estimated average weight is lb. Page Winter Driving Tips Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. Pre-winter preparations l Use fluids that are appropriate to the prevailing outside tem- peratures.
Driving information When driving the vehicle Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. When parking the vehicle Park the vehicle and move the shift lever to P automatic trans- mission , 1 or R manual transmission without setting the park- ing brake. Driving information Regulations on the use of snow chains l Regulations regarding the use of tire chains vary according to loca- tion and type of road.
Always check local regulations before install- ing chains. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters. Page Trailer Towing For your safety and the safety of others, do not overload the vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Weight limits Confirm that the total trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits.
Page Total trailer weight Tongue load Towing a trailer Contact your Toyota dealer for further information about additional requirements such as a towing kit, etc. Hitch Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Page Break-in schedule Toyota recommends that you do not use a new vehicle or a vehicle with any new power train components engine, transmission, differential, wheel bear- ings, etc.
Page When towing a trailer If the gross trailer weight exceeds lb. Never tap into your vehicle's hydraulic system, as this will lower the vehi- cle's braking effectiveness. Do not install the trailer hitch on the bumper; this may cause body damage.
Do not use axle-mounted hitches, as they can cause damage to the axle housing, wheel bearings, wheels or tires. Driving information l Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to right. Driving information l In order to maintain efficient engine braking and electrical charging performance, do not use overdrive automatic transmission or the 5th gear manual transmission.
Page Dinghy Towing Automatic Transmission Driving information Dinghy towing automatic transmission Your vehicle is not designed to be dinghy towed with 4 wheels on the ground behind a motor home. Page Dinghy Towing Manual Transmission Driving information Dinghy towing manual transmission Your vehicle can be dinghy towed in a forward direction with 4 wheels on the ground behind a motor home.
Towing your vehicle with 4 wheels on the ground To prevent damage to your vehicle, perform the following procedures before towing. Doing so may cause serious damage.
Using the air conditioning system and defogger Automatic air conditioning system if equipped Air outlets and fan speed are automatically adjusted according to the temperature setting.
Using the air conditioning system and defogger Air flows to the upper body and feet. Recirculated air mode will auto- matically switch to outside air mode. Using the air conditioning system and defogger Defogging the windshield Defogging The air conditioning system con- trol operates automatically. It is not possible to return to recirculated air mode when the switch is on.
Using the air conditioning system and defogger Using the automatic mode Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions. As a result, the following may occur. The system may switch automatically to recirculated air mode when the coolest temperature setting is selected in summer. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.
Page Manual Air Conditioning System Using the air conditioning system and defogger Adjusting the settings Adjusting the temperature setting heater Turn the temperature control dial clockwise to increase the temper- ature.
Adjusting the temperature setting air conditioning system Turn the temperature control dial clockwise warm or counter- clockwise cool. The air intake is automatically switched to outside air mode. Using the air conditioning system and defogger Air flows to the windshield and side windows. It is not possible to return to recircu- lated air mode when the switch is Switching air intake modes Press The mode switches between outside air mode indicator off and recircu Using the air conditioning system and defogger Adjusting the position of and opening and closing the air outlets Center outlets Direct air flow to the left or right, up or down.
Right and left side outlets Direct air flow to the left or right, up or down. For quick clearing of the windshield and side windows vehicles with air conditioning system Press to turn the air conditioning on. Using the air conditioning system and defogger NOTICE To prevent battery discharge Do not leave the air conditioning system on longer than necessary when the engine is stopped.
Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers Clear the rear window using the defogger. Page Using The Audio System Using the audio system Title Page Using the radio P.
To avoid damaging the audio system Take care not to spill drinks or other fluids over the audio system. Page Using The Radio Using the audio system Scanning all radio stations within range STEP Press All stations with reception will be played for 5 seconds each. STEP When the desired station is reached, press once again. Contact your Toyota dealer.
Using the audio system When the battery is disconnected Station presets are erased. Reception sensitivity Maintaining perfect radio reception at all times is difficult due to the con- tinually changing position of the antenna, differences in signal strength and surrounding objects, such as trains, transmitters, etc.
The radio antenna is mounted inside the rear window. Page XM antenna cable is attached securely. See a Toyota certified dealer. Using the audio system The channel you selected is no longer available. If it does not change automatically, select another channel. Page Using The Cd Player The indicator on the slot turns to amber when the CD is inserted.
Using the audio system Fast-forwarding and reversing tracks To fast-forward or reverse, press reverse or fast-for- ward. STEP Press again when the desired track is reached. Tracks are played in a random order until is pressed once more. Tracks on all loaded CDs are played in a random order until pressed once more. Page Operation has stopped due to a high temperature inside the player.
Wait for a while and then press. Contact your Toyota dealer if the CD still cannot be played back. Discs that can be used Discs with the marks shown below can be used. CDs that have a diameter that is not 4. Do not insert anything other than CDs into the CD slot. Do not apply oil to the CD player. Store CDs away from direct sunlight.
Selecting the desired folder by cueing the first file of each folder Press and hold until you hear a beep. To repeat all of the files in a folder Press and hold RPT until you hear a beep. Contact your Toyota dealer if the CD still cannot be played. This format compresses audio data to a size smaller than that of the MP3 format. Using the audio system Compatible disc formats The following disc formats can be used. Using the audio system IExtensions If the file extensions.
This may result in large amounts of interference and damage to the speakers. Using the audio system Adjusting sound quality and volume balance Turning adjusts the level.
ASL automatically adjusts the volume and tone quality according to vehi- cle speed. Page Using The Aux Adapter Open the cover and connect STEP the portable audio device. Press STEP Operating portable audio devices connected to the audio system The volume can be adjusted using the vehicle's audio controls. Using the audio system Using the steering wheel audio switches if equipped Some audio features can be controlled using the switches on the steering wheel. Press and hold the switch to continue increasing or decreasing the vol- ume.
STEP Press and hold until you hear a beep. Using the hands-free phone system for cellular phone FCC WARNING: Changes or modifications in construction not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Using the hands-free phone system for cellular phone Using the hands-free phone system for cellular phone if equipped Audio unit Displays such items as message, name, and phone number Lower-case characters and special characters, such as an umlaut, can- not be displayed. Using the hands-free phone system for cellular phone Steering wheel Volume The voice guidance volume cannot be adjusted by using this button.
Using the hands-free phone system for cellular phone Microphone Vehicles with moon roof Vehicles without moon roof I n f o r ma t i o n P r o v i d e d b y Using the hands-free phone system for cellular phone Operating the system by using a voice command By following voice guidance instructions output from the speaker, voice commands can be given to allow for operation of the hands- free phone system without checking the display or operating Operation procedure when using a voice command Press the talk switch and say the command for a desired function.
Using the hands-free phone system for cellular phone Using the hands-free phone system for the first time Before using the hands-free phone system, it is necessary to register a cellular phone in the system. The phone registration mode will be entered automatically when starting the system with no cellular phone registered.
Using the hands-free phone system for cellular phone Menu list of the hands-free phone system Normal operation Second First menu Third menu Operation detail menu Dialing a number stored in Callback the incoming call history memory Dialing a number stored in Redial the outgoing call history memory Page Making A Phone Call STEP Select a registered name to be input by either of the following methods: a.
Press the talk switch and say a registered name. Using the hands-free phone system for cellular phone Transferring a call A call can be transferred between the cellular phone and system while dialing, receiving a call, or during a call. Use one of the follow- ing methods: a.
Operate the cellular phone. Refer to the manual that comes with the cellular phone for the oper- ation of the phone. Page Setting A Cellular Phone Using the hands-free phone system for cellular phone Setting a cellular phone Registering a cellular phone in the hands-free phone system allows the system to function.
The following functions can be used for reg- istered cellular phones: Functions and operation procedures To enter the menu for each function, follow the steps below by using a voice command or l Registering a cellular phone Page Security And System Setup Using the hands-free phone system for cellular phone Security and system setup To enter the menu of each setting, follow the steps below: Security setting items and operation procedure l Setting or changing the PIN Personal Identification Number 1.
To decrease the volume: Turn counterclockwise. To increase the volume: Turn clockwise. Page Using The Phone Book Using the hands-free phone system for cellular phone Using the phone book To enter the menu of each setting, follow the steps below: l Adding a new phone number 1.
Input the phone number 1 digit at a time. Press the talk switch and say the desired name. Using the hands-free phone system for cellular phone STEP Select the desired preset button, and register the data into speed dial by either of the following methods: a.
Pressing the talk switch while the desired data is being read aloud selects the data, and the following function will be available.
Page Using The Interior Lights The time elapsed before lights turn off can be changed. Page Interior Light Page Using The Storage Features Using the storage features List of storage features Auxiliary boxes Glove box Bottle holders Cup holders Console box I n f o r ma t i o n P r o v i d e d b y
Toyota - Corolla - Workshop Manual - 2009 - 2020.2009 toyota corolla manual
Press the "LOCK" button to arm the system. With the open palm lightly slap the "A" pillar by the driver's windshield. You should hear short chirps from the vehicle horn. Allow a few seconds for the shock to settle, then conduct the same check at various points around the vehicle. Sensitivity can be adjusted at the shock sensor for best response.
Slap the vehicle at the "A" pillar with slightly more force. The vehicle should go into full alarm. Rearm the vehicle and conduct the same check at various points around the vehicle. Page 15 of 17 Rear Cover F. Set in the driver's seat with all the doors closed. Insert the ignition key and turn to the start position. The starter should not crank the engine. Turn to the start position.
The starter should crank the engine. Exit vehicle. Use the key to unlock and open the driver's door. The alarm will sound. Enter the vehicle, insert the ignition key and turn to the on position. Press the valet control switch once, the alarm should deactivate and the vehicle should now start.
Press the "LOCK" button, the system should arm and lock all doors. Rearm the security system by pressing the "LOCK" button. Open any door or hatch. The system should simultaneously sound the horn and flash the parking lights. The system should sound 4 chirps of the horn, the parking lights should flash 4 times, indicating vehicle intrusion. The LED should indicate the point of intrusion after disarming the system. Observe the LED for 1, 2, or 3 flashes.
Compare your observations to the following. Refer again to the vehicle repair manual and re-assemble all panels that were removed. Test thoroughly, all mechanical and electrical components disconnected and or removed from the vehicle during the installation of this accessory.
Turn the ignition key to the on position. You will hear 2 chirps to confirm that the chirps were turned off. LED Place the system into Valet mode. VPC only 1. The switch is in the in position, and the red LED light is turned on solid, indicating that the system is in the Valet Mode.
Applying the window warning decal: 1. Apply the window warning decals to the driver side and passenger side windows, just above the anti-theft radio stickers if equipped. If not equipped, apply the decals at the lower rear edge of the window. The decals are reverse printed and are applied to the inside surface of the glass. Owners Manual: 1. Leave the Keyless Entry Security owner's manual in the vehicle glove box. If this happens, simply start over. Ending in the OFF position. Page 63 Page 64 Vehicles without smart key system The key is in the engine switch and either of the front door is open.
Customization that can be configured at Toyota dealer Settings e. Opening, closing and locking the doors and trunk Trunk The trunk can be opened using the entry function, wireless remote control, key or trunk opener. Page 66 Opening, closing and locking the doors and trunk Trunk opener cancelling system To protect luggage stored in the trunk against theft, do the following procedure.
Turn the master key vehicles without smart key system or mechanical key vehicles with smart key system counterclock- wise to lock the trunk opener fea- ture. Page 67 This not only keeps personal belongings from being thrown out, but also pre- vents exhaust gases from entering the vehicle. When children are in the vehicle Never leave children unattended in the vehicle as they may lock them- selves in the vehicle or trunk, which could cause the child to overheat or suffocate, resulting in death or serious injury.
Adjustable components seats, mirrors, steering wheel Front seats Power seat driver's side only Seat position switch Seatback angle switch Seat cushion front angle switch Vertical height adjustment switch Lumbar support switch I n f o r ma t i o n P r o v i d e d b y Page 69 Page 70 Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt.
If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of Page Rear Seats Adjustable components seats, mirrors, steering wheel Rear seats Before folding down the rear seat Stow the rear outside seat belt buckles and move the rear center seat belt buckle as shown.
Folding down rear seatbacks Pull the seatback lever in the trunk for the seatback you wish to fold down. Page 72 Failure to do so may result in death or serious injury. Make sure the seatback is securely locked by pressing forward and rear- ward on the top of the seatback. Page Head Restraints Adjustable components seats, mirrors, steering wheel Head restraints Front seats Vertical adjustment Push and hold the lock release button when lowering the head restraint. Removal Pull the head restraint up while pressing the lock release but- ton.
Rear seats Adjusting the height of the head restraints Make sure that the head restraints are adjusted so that the center of the head Page 74 Use the head restraints designed for each respective seat. Adjust the head restraints to the correct position at all times.
After adjusting the head restraints, push down on them and make sure they are locked in position. Page Seat Belts Adjustable components seats, mirrors, steering wheel Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. Correct use of the seat belts l Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the Page 76 Adjustable components seats, mirrors, steering wheel Adjusting the height of the belt front seats Down Move the height adjuster up and down as needed.
Seat belt comfort guide outside rear seats If the shoulder belt sits close to a person's neck, use the seat belt comfort guide. Page 77 Adjustable components seats, mirrors, steering wheel Buckle, position and release the STEP seat belt. Seat belt pretensioners front seats The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal collision.
Page 78 Adjustable components seats, mirrors, steering wheel Emergency locking retractor ELR The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
Page 79 Toyota dealer free of charge. Rear outside seat belt Use the seat belt after passing it through the guide if the seat belt comes free from the guide. Page 80 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. Page 81 Ensure that the belt and tab are locked and the belt is not twisted.
If the seat belt does not function correctly, immediately contact your Toyota dealer. Replace the seat assembly, including the belts, if your vehicle has been involved in a serious accident, even if there is no obvious damage. Page 82 Adjustable components seats, mirrors, steering wheel CAUTION Using a seat belt extender Do not wear the seat belt extender if you can fasten the seat belt without the extender.
Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or injury in the event of a collision. Page Steering Wheel Adjustable components seats, mirrors, steering wheel Steering wheel The steering wheel can be adjusted to a comfortable position.
STEP Hold steering wheel and press the lever down. STEP Adjust to the ideal position by moving the steering wheel hori- zontally and vertically. Adjustable components seats, mirrors, steering wheel Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions. Manual anti-glare inside rear view mirror Normal position Anti-glare position Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.
Page 85 Adjustable components seats, mirrors, steering wheel To prevent sensor error To ensure that the sensors operate prop- erly, do not touch or cover them. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury. Page Outside Rear View Mirrors Adjustable components seats, mirrors, steering wheel Outside rear view mirrors Mirror angle can be adjusted using the switch.
Select a mirror to adjust. Page 87 When the mirrors are fogged up vehicles with outside rear view mirror defoggers Turn on the mirror defoggers to defog the mirrors. Page 88 Opening and closing the windows Power windows if equipped The power windows can be opened and closed using the following switches. Lock switch Press the switch down to lock the passenger window switches. Page 89 Operating the power windows after turning the engine OFF Vehicles with smart key system The power windows can be operated for approximately 45 seconds after the Opening and closing the windows Moon roof if equipped Use the overhead switches to open, close, and tilt the moon roof up and down.
Push the switch again to fully open. Page 91 Operating the moon roof after turning the engine OFF Vehicles with smart key system The moon roof can be operated for approximately 45 seconds after the Page 92 Failing to do so may cause death or serious injury. Do not allow any passengers to put their hands or heads outside the vehi- cle while it is moving.
Do not sit on top of the moon roof. Page Refueling Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. Vehicles without smart key system Turn the engine switch OFF and ensure that all the doors and windows are closed.
Page 94 Closing the fuel tank cap When replacing the fuel tank cap, turn it until a clicking sound is heard. After releasing your hand, the cap will turn slightly to the opposite direction. Page 95 This may cause static electricity to build up, resulting in a possible ignition hazard.
When replacing the fuel cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury. Page 96 Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle's painted surface.
Page Theft Deterrent System Theft deterrent system Engine immobilizer system The vehicle's keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle's on-board computer.
Never leave the keys inside the vehicle when you leave the vehicle. Page 98 Theft deterrent system Certifications for the engine immobilizer system for vehicles sold in U. Theft deterrent system Theft prevention labels for U. These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law.
Page Safety Information Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back in the seat. Page Doing so could cause the driver to lose control of the vehicle.
Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger. Page Srs Airbags Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.
Front airbags Driver airbag and front passenger airbag Can help protect the head and chest of the driver and front pas Safety information The main SRS airbag system components are shown above. The SRS airbag system is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sensor and an airbag sensor.
In certain types of severe frontal or side impacts, the SRS airbag sys- tem triggers the airbag inflators. Safety information Side airbags and curtain shield airbags if equipped The SRS side airbags and curtain shield airbags are designed to inflate when the passenger compartment is subjected to a severe impact from the side. Depending on the conditions and type of accident, there are times when the curtain shield airbags may deploy inflate in a front impact.
Safety information Types of collisions that may not deploy the SRS side airbags and cur- tain shield airbags if equipped The SRS side airbags and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a col- lision to the side of the vehicle body other than the passenger compartment. Safety information When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible.
Do not disconnect the battery cables before contacting your Toyota dealer. Any of the SRS airbags have been inflated. Failure to do so may cause death or serious injury.
The driver and all passengers in the vehicle must wear their seat belts properly. The SRS airbags are supplemental devices to be used with the seat belts. The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag. Page An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem.
Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are the safest for infants and children. Do not drive the vehicle while the driver or passenger has items resting on their knees. Safety information CAUTION SRS airbag precautions Vehicles with side airbags and curtain shield airbags: Do not attach anything to areas such as the door, windshield glass, side door glass, front and rear pillars, roof side rail or assist grip.
Curtain shield airbags: Do not hang coat hangers or other hard objects on the coat hooks. Page Vehicles without side airbags and curtain shield airbags: If the areas where the SRS airbags are stored, such as the steering wheel pad are damaged or cracked, have them replaced by your Toyota dealer.
Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for the front passenger.
Safety information : Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable.
Page Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately.
Child restraint systems installed on the rear seat should not contact the front seatbacks. Page Child Restraint Systems The laws of all 50 states of U. Safety information Types of child restraints Child restraint systems are classified into the following 3 types according to the age and size of the child. Page In an accident, the child can be crushed against the windshield, or between you and the vehicle's interior. Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat.
According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the rear-facing child restraint system is installed on the front passenger seat.
Page Installing Child Restraints Safety information Installing child restraints Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the rear seats using a seat belt or a child restraint lower anchorage.
Attach the top strap when installing a child restraint. Run the seat belt through the STEP child seat and insert the plate into the buckle. Safety information While pushing the child seat STEP down into the rear seat, allow the shoulder belt to retract until the child seat is securely in place. After shoulder belt retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended. Safety information While pushing the child seat into STEP the rear seat, allow the shoulder belt to retract until the child seat is securely in place.
Safety information Removing a child restraint installed with a seat belt Push the release button and fully retract the seat belt. Installation with child restraint lower anchorages Rear right seat only: Slide the STEP rear center seat belt to the side to prevent it from getting pinched in the lower anchorage. STEP Latch the hooks of the lower straps onto the anchors. If the child restraint has a top strap, the top strap should be latched onto the anchors.
Safety information Child restraint systems with a top strap STEP Secure the child restraint using a seat belt lower anchor, and do the following.
Outside Remove the head restraint. Center Lock the head restraint in place at the lowest position. Open the anchor bracket cover, STEP latch the hook onto the anchor This vehicle is designed to confirm to the SAE J Safety information CAUTION When installing a child restraint system When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder.
The belt should be kept away from the child's neck, but not so that it could fall off the child's shoulder. Page Driving Procedures Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. STEP Set the parking brake. Page Breaking in your new Toyota To extend the life of the vehicle, the following precautions are recommended Driving procedures Operating your vehicle in a foreign country Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel.
Page Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immedi- ately. Do not under any circumstances shift the shift lever to P vehicles with an automatic transmission or R while the vehicle is moving. Driving procedures CAUTION When driving on slippery road surfaces Sudden braking, acceleration and steering may cause tire slippage and reduce your ability to control the vehicle, resulting in an accident.
Sudden changes in engine speed, such as engine braking caused by up- shifting or down-shifting, may cause the vehicle to skid, resulting in an accident. Page The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard.
Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard. After shifting, do not release the clutch abruptly. Doing so may damage the clutch, tran- saxle and gears. Do not rest your foot on the clutch pedal while driving.
Doing so may cause clutch trouble. Page If you hear a squealing or scraping noise brake pad wear limit indica- tors Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage can result if the pads are not replaced when needed. Starting the engine STEP Have the vehicle inspected by your Toyota dealer immediately. Do not depress the accelerator pedal while starting the engine under any circumstances.
Doing so may cause an accident resulting in death or serious injury. Driving procedures Engine ignition switch vehicles without smart key system Starting the engine Automatic transmission STEP Check that the parking brake is set. To free it, turn the key while turn- ing the steering wheel slightly in either direction. If the engine does not start The engine immobilizer system may not have been deactivated. When starting the engine 2. Page Automatic Transmission Driving procedures Automatic transmission if equipped Select a shift position appropriate for the driving conditions.
Driving procedures Changing shift ranges in S mode multi-mode type Shift the shift lever to the S position and operate the shift lever. Upshifting Downshifting The initial shift range in S mode is automatically set to 4 or 5.
Shift ranges and their functions Shift range Function Page S multi-mode type This may indicate a malfunction in the automatic transmission system. In this situation, the vehicle will operate as if the shift lever is in D. Page Manual Transmission Driving procedures Manual transmission if equipped Shifting the shift lever Fully depress the clutch pedal before operating shift lever, and then release the clutch pedal slowly.
Maximum allowable speeds Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary. Page Turn Signal Lever Driving procedures Turn signal lever Left turn Right turn Move and hold the lever partway to signal a lane change. The left hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change. Page Parking Brake Driving procedures Parking brake Sets the parking brake Fully set the parking brake U.
Canada while depressing the brake pedal. Releases the parking brake Slightly raise the lever and lower it completely while press- ing the button. Page Instrument Cluster Pressing and holding the button will reset the trip meter when the trip meter is being displayed.
To adjust the brightness of the instrument panel light, turn the button. Tachometer Displays the engine speed in revolutions per minute.
Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Instrument cluster Odometer and trip meter display Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently.
Page Indicators And Warning Lights Instrument cluster Optitron type meters Non-Optitron type meters I n f o r ma t i o n P r o v i d e d b y Page Have the vehicle inspected by your Toyota dealer immediately if this occurs. Page Multi-Information Display Instrument cluster Multi-information display The multi-information display presents the driver with a variety of driving-related data, including the clock and the outside tempera- ture. Instrument cluster l Outside temperature Displays the outside air temperature.
Instrument cluster l Average vehicle speed Displays the average vehicle speed since the engine was started or since the function was reset. The function can be reset by pressing the display but- ton for longer than one second when the average vehicle speed is displayed.
Instrument cluster When disconnecting and reconnecting battery terminals The following information data will be reset. Clock Average fuel consumption Driving range Average vehicle speed Elapsed time NOTICE The multi-information display at low temperatures Allow the interior of the vehicle to warm up before using the liquid crystal information display.
Operating the lights and wipers Headlight switch side marker, parking, tail, license plate and instrument U. The headlights and all lights listed above turn on. Operating the lights and wipers Daytime running light system To make your vehicle more visible to other drivers, the headlights turn on automatically whenever the engine is started and the parking brake is released.
The brightness of headlights will automatically change depending on the darkness of the surroundings. Page Fog Light Switch Operating the lights and wipers Fog light switch if equipped The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam. Page Windshield Wipers And Washer Operating the lights and wipers Windshield wipers and washer Wiper can be operated manually.
Intermittent windshield wiper interval mode if equipped Wiper intervals can be adjusted for intermittent operation. Page Using Other Driving Systems Using other driving systems Cruise control if equipped Use cruise control to maintain a set speed without using the acceler- ator. Press the button once more to deactivate the cruise control. Using other driving systems Canceling and resuming regular acceleration Cancel Pull the lever towards you to cancel cruise control. The speed setting is also can- celed when the brakes are applied or the clutch pedal manual transmission depressed.
Resume To resume cruise control and return to the set speed, push the lever up. Page If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Contact your Toyota dealer and have your Toyota inspected. Page Driving Assist Systems Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations.
Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle.
ABS Anti-lock Brake System Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface. You may need to turn the system off to enable you to rock the vehicle in order to free it.
EPS operation sound When the steering wheel operates, a motor sound whirring sound may be heard. Contact your Toyota dealer for further information when replacing tires or wheels.
Handling of tires and suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction. Page Driving Information Driving information Cargo and luggage Take notice of the following information about storage precau- tions, cargo capacity and load.
Be sure all items are secured in place. Placing the weight as far for- ward as possible helps maintain vehicle balance. Driving information 6 If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Keep cargo and luggage low, as close to the floor as possible.
Never allow anyone to ride in the enlarged trunk. It is not designed for passengers. Page Vehicle Load Limits Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. Total load capacity: lb. Seating capacity: 5 occupants Front 2, Rear 3 Seating capacity means the maximum number of occupants whose estimated average weight is lb.
Page Winter Driving Tips Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter.
Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. Pre-winter preparations l Use fluids that are appropriate to the prevailing outside tem- peratures.
Driving information When driving the vehicle Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. When parking the vehicle Park the vehicle and move the shift lever to P automatic trans- mission , 1 or R manual transmission without setting the park- ing brake.
Driving information Regulations on the use of snow chains l Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters. Page Trailer Towing For your safety and the safety of others, do not overload the vehicle or trailer.
Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Weight limits Confirm that the total trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits. Using the hands-free phone system for cellular phone Using the interior lights Using the storage features Other interior features Maintenance and care Maintenance Do-it-yourself maintenance Essential information Steps to take in an emergency Specifications Customization Initialization Reporting safety defects for U.
Need help? Ask a question. My truck will not close. Answer this question. How do I convert miles into kilometres? The location of the VIN number of the car differs per brand and type of car. The code may be stamped on the frame of the car or mounted on a plate. It is best to consult the manual of the Toyota Corolla for the exact location of the VIN number.
What is a VIN number? The VIN number of a car is an identification number unique to each car. When does my Toyota need maintenance?
No comments:
Post a Comment